无忧启动论坛

标题: 请教外置程序ISO怎么改成ISZ格式 [打印本页]

作者: fyhfyhfyh 时间: 2008-11-15 20:45
标题: 请教外置程序ISO怎么改成ISZ格式
我想把外置程序格式换成ISZ 这样体积要小的多不知道怎么改？
下面是批文件

文件名：WINPEFILES.CMD

@echo off
set ff=winpefiles
for %%x in (A B C D E F G H I J K L M N O P Q R S T U V W) DO if exist %%x:\外置程序\winpe.ini goto end
for %%x in (A B C D E F G H I J K L M N O P Q R S T U V) DO (
if exist %%x:\bootcd.iso set fn=%%x:\bootcd.iso
if exist %%x:\bootcd.iso GOTO iso
if exist %%x:\%ff%.iso set fn=%%x:\%ff%.iso
if exist %%x:\%ff%.iso GOTO iso
if exist %%x:\%ff%.img set fn=%%x:\%ff%.img
if exist %%x:\%ff%.img GOTO img
)
goto end

:iso
REG ADD "HKCU\Software\Towodo Software\Virtual Drive Manager\Settings" /f /v MountPrevious /t REG_DWORD /d 1 >nul
REG ADD "HKCU\Software\Towodo Software\Virtual Drive Manager\Settings" /f /v XbtnQuit /t REG_DWORD /d 0 >nul
REG ADD "HKCU\Software\Towodo Software\Virtual Drive Manager\Settings" /f /v LastMounts /t REG_MULTI_SZ /s ! /d W:!自动侦测!%fn%!1 >nul
REG ADD "HKCU\Software\Towodo Software\虚拟驱动器\Settings" /f /v MountPrevious /t REG_DWORD /d 1 >nul
REG ADD "HKCU\Software\Towodo Software\虚拟驱动器\Settings" /f /v XbtnQuit /t REG_DWORD /d 0 >nul
REG ADD "HKCU\Software\Towodo Software\虚拟驱动器\Settings" /f /v LastMounts /t REG_MULTI_SZ /s ! /d W:!自动侦测!%fn%!1 >nul
goto vdm
:img
REG ADD "HKCU\Software\Towodo Software\Virtual Drive Manager\Settings" /f /v MountPrevious /t REG_DWORD /d 1 >nul
REG ADD "HKCU\Software\Towodo Software\Virtual Drive Manager\Settings" /f /v XbtnQuit /t REG_DWORD /d 0 >nul
REG ADD "HKCU\Software\Towodo Software\Virtual Drive Manager\Settings" /f /v LastMounts /t REG_MULTI_SZ /s ! /d W:!自动侦测!%fn%!%imgro% >nul
REG ADD "HKCU\Software\Towodo Software\虚拟驱动器\Settings" /f /v MountPrevious /t REG_DWORD /d 1 >nul
REG ADD "HKCU\Software\Towodo Software\虚拟驱动器\Settings" /f /v XbtnQuit /t REG_DWORD /d 0 >nul
REG ADD "HKCU\Software\Towodo Software\虚拟驱动器\Settings" /f /v LastMounts /t REG_MULTI_SZ /s ! /d W:!自动侦测!%fn%!%imgro% >nul
:vdm
start vdm1.exe /i
echo ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
echo 稍等片刻......
echo ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
:Wait
pecmd wait 1000
IF NOT EXIST W: GOTO Wait
if exist W:\外置程序\winpe.ini pecmd load W:\外置程序\winpe.ini
:end

[ 本帖最后由 fyhfyhfyh 于 2008-11-16 09:41 编辑 ]

作者: xiao75918 时间: 2008-11-16 10:30
不懂什么意思，isz格式是压缩的镜像格式，Virtual Drive Manager好像不支持isz格式，isz是ultraiso软件制作的压缩镜像，需要其虚拟光驱程序挂载（isocmd.exe与isodrive.sys）,不知你用的是哪款pe,
东邪思想 PE_DIY版\完美者V7\nanope2008都支持isz格式，把你的外置放入其isz中就可以了。

欢迎光临无忧启动论坛 (http://bbs.wuyou.net/)