RUN 1206 更新支持磁盘交换,文件检索,自动菜单,自动列表,全自动安装nt5x系统

2012apple3000 · 发表于 2013-6-20 10:21:54

本帖最后由 2012apple3000 于 2013-6-20 10:24 编辑

sratlf 发表于 2013-6-20 09:42
sorry, you means you have tried to press Enter for step 1, and after the reboot, run the command a ...

Sorry, I made a mistake.

I used 2003.iso located my USB-HDD. so it had bluescreen or disk CD not found error. But why not ISO in USB-HDD?

I tried again in my HDD. without --mem.
Good^^.

I tried tweak CD , 6 in 1 windows 2003. I tried MSDN windows2003 vlk , too.
No problem.

At 1 step, file copied.
and 2 step, 1st time swap S, Enter. 2st time press H you said.
yes. find ntldr and boot from (HD1,0).
very very thanks.

Without --mem, I installed w2k. very thanks.

and at AHCI mode I succeeded.

run --wvbk --dpms:/dpms.iso iso=/2003.iso

press F6, and find AHCI 10 controller, defined that. so succeeded.

I have question.

When try with ISO in USB-HDD, At 2 Step, have No disk CD, or have bluescreen. Why?

is ISO Only located in HDD?

Another question.
my HDD 3 partition, 1st partition is win7 installed. 1st partition is Activated.
and 2nd partition will be installed 2003.
So Grub boot with run, After install 2003 to 2nd partition, Drive letter is Not C.

From 527104427 , I solved. Just makeactive hd~.

in grub,
For activate partition, example , makeactive (hd1,0)

I did not need hide 1st partition As you said.

maybe with run, how to do " makeactive hd~?

527104427 · 发表于 2013-6-20 10:55:34

以前就发现了这个问题，把ISO放在U盘上，第二阶段可以发现ISO；但把ISO放在移动硬盘上，第二阶段有可能找不到ISO。

具体原因不明，期待解决……

sratlf · 发表于 2013-6-20 11:15:40

2012apple3000 发表于 2013-6-20 10:21
Sorry, I made a mistake.

I used 2003.iso located my USB-HDD. so it had bluescreen or disk CD ...

the 1st question, maybe the usb devices are not ready to use at that time, so system cannot find the iso file located at usb device.

the 2nd question, RUN cannot makeactive any partitions, so you have to makeactive the partition manually before it...

2012apple3000 · 发表于 2013-6-20 11:39:22

sratlf 发表于 2013-6-20 11:15
the 1st question, maybe the usb devices are not ready to use at that time, so system cannot find ...

Thanks.
I booted from USB-HDD grub. and Command RUN.
Ummm...At step1, win install system showed Hdd 3 partitions and my USB-HDD 3 partitions.
And selected HDD -1 partition and Copied OS Files.

why at step2, can system not finded the iso?

then, I should use " --mem" For using ISO file located at USB-HDD.

2012apple3000 · 发表于 2013-6-20 11:40:43

527104427 发表于 2013-6-20 10:55
以前就发现了这个问题，把ISO放在U盘上，第二阶段可以发现ISO；但把ISO放在移动硬盘上，第二阶段有可能找不 ...

Yes, I hope that.

sratlf · 发表于 2013-6-20 11:51:49

2012apple3000 发表于 2013-6-20 11:39
Thanks.
I booted from USB-HDD grub. and Command RUN.
Ummm...At step1, win install system showed ...

yes, you are right, if use --mem, win system will find the iso file in the memory, installation can be continued.
but if not, win system will try to find the iso file on all storage devices, unfortunately, if the usb storage devices are all not ready to use at this time, win system cannot find the iso file, so the fail message will be showed to you.

woey · 发表于 2013-6-20 21:57:58

thanks !! the file is very good

sratlf · 发表于 2013-6-20 23:14:03

527104427 发表于 2013-6-18 18:19
希望S大能更新一下模板，应该增加了不少新命令吧

新版模板已更新 0620版

527104427 · 发表于 2013-6-21 07:38:27

sratlf 发表于 2013-6-20 23:14
新版模板已更新 0620版

多谢，下载学习

假大空 · 发表于 2013-6-21 08:55:04

S大，自动菜单方式对文件夹里的文件数量和大小有限制吗？今天测试--automenu-all参数进不了硬盘上的一个目录。在win下看了该文件夹包含3942个文件，523个文件夹，18G大小。错误信息error 27:unrecognized command...
用Z大的0531版run自动菜单方式能进到这个文件夹里去。

sratlf · 发表于 2013-6-21 09:17:57

假大空发表于 2013-6-21 08:55
S大，自动菜单方式对文件夹里的文件数量和大小有限制吗？今天测试--automenu-all参数进不了硬盘上的一个目录 ...

这个确实有问题不过一直没找到原因那个错误提示是在setlocal执行时出现的怀疑是循环次数过多还没找到解决办法

2012apple3000 · 发表于 2013-6-21 15:52:47

hi .
I wanna boot winPE. but PE has not RAID DRIVER , SI3112R.
So Can I boot PE by using dpms?

How to do command parse?

RUN --fira dpms:/dpms.lzma iso=/winpe.iso?

sratlf · 发表于 2013-6-21 17:34:38

2012apple3000 发表于 2013-6-21 15:52
hi .
I wanna boot winPE. but PE has not RAID DRIVER , SI3112R.
So Can I boot PE by using dpms?

yes, or boot cd directly by using RUN --fira-isonly dpms:/dpms.lzma iso=/winpe.iso

fyq · 发表于 2013-6-21 17:39:24

等到新模板了，谢谢S大

2011cwj6958 · 发表于 2013-6-21 19:15:25

本帖最后由 2011cwj6958 于 2013-6-21 19:24 编辑

新模板非常好用。打包后放在UD区以iso文件整体启动或者解开启动，都正常。还可以随机更换菜单背景，非常感谢！！！！！！！！

nytc006 · 发表于 2013-6-23 08:43:22

有点疑惑，请教一下S大：我的16G的金士顿u盘，ud方式启动。在大部分电脑都是被识别为HD0的……
试了一下您这个run的 run --nt 以代替我的主菜单之前的[尝试从本机已有的系统启动]项。
但选择该菜单后，跳出了手动交换磁盘的界面。如果我不交换，它就会从本地引导失败，交换则成功
我就是奇怪：因为您这个本来就是推荐在U盘引导启动事才使用的，这个交换的动作难道也得加了--swap？

2012apple3000 · 发表于 2013-6-23 18:40:46

sratlf 发表于 2013-6-21 17:34
yes, or boot cd directly by using RUN --fira-isonly dpms:/dpms.lzma iso=/winpe.iso

Thanks.
A : --fira-isonly dpms:/dpms.lzma iso=/winpe.iso
B : --fira-isonly dpms:/dpms.lzma /winpe.iso
is same?
Can I use --wvbk-only:/winvblk.img instead of --fira-only ?

And.
How to make DPMS.ISO to lzma ?
I Extracted lzma. and DPMS file is in it. I attached .ISO to DPMS
and I opened DPMS.ISO with UltraISO.

After edit, detach .ISO and packed with 7-zip archieve.
Am I right?

As seperately lzma, For example, intel.lzma. SiliconImage.lzma and etc..
Can I make it Same method?

sratlf · 发表于 2013-6-23 22:46:34

nytc006 发表于 2013-6-23 08:43
有点疑惑，请教一下S大：我的16G的金士顿u盘，ud方式启动。在大部分电脑都是被识别为HD0的……
试了一下您这 ...

用--nt参数时如果u盘被识别为hd设备会自动提示是否交换磁盘防止打算引导本地系统时错误的从u盘引导

sratlf · 发表于 2013-6-23 23:17:25

2012apple3000 发表于 2013-6-23 18:40
Thanks.
A : --fira-isonly dpms:/dpms.lzma iso=/winpe.iso
B : --fira-isonly dpms:/dpms.lzma /win ...

yes, they are the same, also the same to command --fira dpms:/dpms.lzma /winpe.iso

yes, you can.

no, just need to download the mass storage driver pack from http://driverpacks.net/driverpacks/latest,
then pack the file DriverPack_....ini and folder D to iso file with UltraISO,
finally use 7-zip to compress the iso file to lzma file.

parameter dpms can only use driver pack download from driverpacks.net, you can try to use parameter srs.

2012apple3000 · 发表于 2013-6-24 08:47:11

Sorry, I Cannot show your Answer All Statement. I can't Click that.
[ yes, they are the same, also the same to command --fira dpms:/dpms.lzma /winpe.iso yes, you can. no, just need to download the mass storage driver pack from http://driverpacks.net/driverpacks/la 详情回复发表于昨天 23:17 ]

where is your answer?

Is it possible that with RUN, I want to boot VHD (win7.vhd or xp.vhd , and vhd's child.)

Chenall's ntboot is possible , but have to load NTBOOT.ISO or command "NTBOOT nt6=/win7.vhd".

Thanks.

sratlf · 发表于 2013-6-24 09:21:12

本帖最后由 sratlf 于 2013-6-24 09:22 编辑

2012apple3000 发表于 2013-6-24 08:47
Sorry, I Cannot show your Answer All Statement. I can't Click that.
[ yes, they are the same, also ...

seems someone deleted my answer... now i recover them, pls check

i am not sure about the vhd file, but you can try --ramos

2012apple3000 · 发表于 2013-6-24 09:33:36

sratlf 发表于 2013-6-24 09:21
seems someone deleted my answer... now i recover them, pls check

i am not sure about the vhd ...

I appreciate your favor.
Concerned to VHD, I will try that.

You said to do pack dpms.iso with 7-zip.
But when I open lzma File, Not dpms.iso , Just dpms .

.ISO , extended name is where?

put D Folder and ini, and save ISO and then Do I detach " .ISO"?
and pack with 7-zip?
am I right?

sratlf · 发表于 2013-6-25 10:01:41

2012apple3000 发表于 2013-6-24 09:33
I appreciate your favor.
Concerned to VHD, I will try that.

sorry for the late response, yes, we can only see the dpms file if we open dpms.lzma via 7-zip, that`s true, but it`s normal...
you can try to map this dpms.lzma to 0xff under grub4dos, and then run ls (0xff)/, you will find all files, so do not need to detach the " .ISO".

2012apple3000 · 发表于 2013-6-25 16:12:07

本帖最后由 2012apple3000 于 2013-6-25 21:36 编辑

sratlf 发表于 2013-6-25 10:01
sorry for the late response, yes, we can only see the dpms file if we open dpms.lzma via 7-zip, th ...

thanks.

xp.vhd is 3Gbyte.

To boot VHD,
1st
RUN --fira disk=/xp.vhd
Not mem (loaded to RAM) and boot to vhd.

2nd
RUN --ramos /xp.vhd
xp.vhd is loaded to RAM (--mem), and it needs much RAM over VHD's size.
but After boot failed with bluescreen and reboot.

So I use 1st parse.
Thanks.

chanel · 发表于 2013-6-26 12:45:42

本帖最后由 chanel 于 2013-6-26 12:52 编辑

sratlf 发表于 2013-6-19 11:26
可以可以用下面的菜单

这个菜单不行，安装MSDN原版XP系统7B黑屏（虚拟机测试），3个驱动方案都试了。

title install nt5
command srsf6
run --swap --fira-none sif iso=/isos/

改成这样则正常

title install nt5
command srsf6
RUN --swap --swap-ext --fira-isonly sif iso=/ISOS/

jh1688 · 发表于 2013-6-27 10:31:52

别用太花俏的，还是老版的好，版本再怎么改，老的总是支持的……

title 启动 Windows NT5 NT6 原版安装（RUN+F6IMG）\n 安装须知：安装NT5自动加载SATA驱动；安装NT6时，\n 当出现：“缺少所需的 CD/DVD器设备驱动程序……”的提示时，\n 按Shift+F10调出CMD窗口，执行D:\\BOOT\\TOOLS\\OSF\\NT6.CMD，\n 安装OSFMOUNT虚拟光驱，手工加载iso文件后，继续安装……
RUN --fira srs sif iso=/iso/
boot

chanel · 发表于 2013-6-27 11:10:08

jh1688 发表于 2013-6-27 10:31
别用太花俏的，还是老版的好，版本再怎么改，老的总是支持的……

title 启动 Windows NT5 NT6 原版安装 ...

大哥，你这句连交换磁盘的机会都没有，这就是所谓的不花哨？

RUN --fira srs sif iso=/iso/

jh1688 · 发表于 2013-6-27 11:18:26

本帖最后由 jh1688 于 2013-6-27 11:27 编辑

你用过了吗？？？？

系统会提示你交换磁盘，等你看清楚磁盘大小，确认后按下“S”键才会下一步，自动交换磁盘在多磁盘机器上苦就有得吃了……

这是最原始的方法，任何版本的RUN都适用，除非S大把他改了，不用这句了……

我刚在我的机器上（实机）运行过，还是能用的……

RUN是最新版0620版的……

chanel · 发表于 2013-6-27 11:45:32

jh1688 发表于 2013-6-27 11:18
你用过了吗？？？？

系统会提示你交换磁盘，等你看清楚磁盘大小，确认后按下“S”键才会下一步，自动交换 ...

大哥，多数情况下不是多硬盘，多数情况下需要交换磁盘，既然这样，为什么不可以先自动交换一下磁盘呢？
再说了，自动交换磁盘后，会自动给出当前hdd0和hdd1的信息，如果不是希望的结果，还可以继续交换，多硬盘也能交换出需要的结果。
算上选择镜像，总共才按两次按键，这也是花哨？

jh1688 · 发表于 2013-6-27 11:57:00

chanel 发表于 2013-6-27 11:45
大哥，多数情况下不是多硬盘，多数情况下需要交换磁盘，既然这样，为什么不可以先自动交换一下磁盘呢？
...

不是大哥，是大叔，快6旬的老人蒙你没有意思，从S大开始写RUN，我一直在玩，所有的参数不敢说全用过，也八九不离十了，所以也就相信了越简单，越好。
交换磁盘，自动也好，手动也好，目的是为了不将系统装到不应该装的地方，因为自动交换磁盘没有提示，在多磁盘机器上就会出现无法预见的灾难，资料的丢失，到时间你哭都没地方去哭……

		自动登录	找回密码
密码			注册

[分享] RUN 1206 更新 支持磁盘交换,文件检索,自动菜单,自动列表,全自动安装nt5x系统

[分享] RUN 1206 更新支持磁盘交换,文件检索,自动菜单,自动列表,全自动安装nt5x系统