菜鸟求救！朗科U208 8G求确认主控芯片方法

2011shazhou_li · 发表于 2011-2-27 23:13:45

刚买了个朗科U208 8G盘，想学学如何量产，下载了ChipGenius查不出芯片信息，拆卸后看到主控芯片写有：115T051LF HVPF4F5  1034  115T051LF-3S-1
下面是ChipGenius查出的信息：
设备名称: [I:]USB Mass Storage Device(Netac OnlyDisk USB Device)

PNP设备ID: VID = 0DD8 PID = 1F08
设备序列号: 001BFC6026F4FAC195912BF7
  设备版本: 1.00

  设备类型: 标准USB设备 - USB2.0高速

芯片制造商: (未查到)
  芯片型号: (未查到)

产品制造商: Netac
  产品型号: OnlyDisk

  资料下载: (暂缺)

[ 本帖最后由 jjsfm 于 2011-3-16 22:39 编辑 ]

jjsfm · 发表于 2011-2-27 23:22:52

先用SSS工具2162读盘试试。

zhtz · 发表于 2011-2-28 13:38:34

是BGA封装吗？
要么是黑片，要么是东芝主控。

2011shazhou_li · 发表于 2011-2-28 22:27:59

谢谢了！等下试试看先！

2011Hock · 发表于 2011-3-9 21:55:39

我的 VID 也是 0DD8 , 也无法读出主控信息.

2011shazhou_li · 发表于 2011-3-10 00:25:29

今天刚刚又试了，还是没搞定

jjsfm · 发表于 2011-3-10 08:28:29

2162工具读盘的结果（截图）？

2011shazhou_li · 发表于 2011-3-10 21:54:32

谢谢版主一直关心！！！用2162工具读盘结果如下：
------------- Device 1------------------
  MP Tool Version : V2.175
  INI File Name : 6692_CM_x2
  Format Date : 2010-12-25 15:17:29
  Flash Part No : Toshiba 3xnm D2 MLC
  CE-0, Flash ID=98-D7-94-32-76-55-0C
  CE-1, Flash ID=98-D7-94-32-76-55-0C
  VID : 0x0DD8
  PID : 0x1F08
  Vendor Name = Netac
  Product Name = OnlyDisk
  Serial Number = 001BFC6026F4FAC195912BF7
  Volume Label =
  F/W Version : 0xB5
  ISP Version : VB3.000B
  Flash R/W Timing : 33.3ns
  Channel : Byte Mode
  Homogeneous Mode : On
  HID Function : Disable
  Planes(F/W) : 1
  Pages/Block : 128 pages
  Max Current : 100 mA
  Total Blocks : 8200
  Bad Blocks : 32
  Capacity : 15595368 Sectors, 7984828416 Bytes
               7797684 KBytes, 7614.93 MBytes, 7.44 GBytes

2011shazhou_li · 发表于 2011-3-10 22:00:08

这个是出错的报告，请版主帮看看
Starting Time: 21:58:48

Device 1:0xB5
MP Version:2.162
INI_File_Name:
Random delay 0 msec
--- Download MP ISP ---
### ROM checksum=0025BE2D
### Err: ROM test failed.(It should be B5,00252F34).

Ending Time: 21:58:53

2011shazhou_li · 发表于 2011-3-10 22:16:30

这个也是刚刚出错的报告，请各位高手一齐帮诊断一下啊，先谢谢啦：
Starting Time: 22:11:50

Device 1:0xB5
MP Version:2.162
INI_File_Name:
Random delay 0 msec
--- Download MP ISP ---
CE-0, Flash ID=98-D7-94-32-76-55-0C-00
CE-1, Flash ID=98-D7-94-32-76-55-0C-00
Found BACKUP Table (000000BB-0001)
Defect Table (00000200-0004)
Original Bad Block - 0:0x0000
Original Bad Block - 0:0x000E
Original Bad Block - 0:0x000F
Original Bad Block - 0:0x00A8
Original Bad Block - 0:0x00A9
Original Bad Block - 0:0x022C
Original Bad Block - 0:0x022D
Original Bad Block - 0:0x05BA
Original Bad Block - 0:0x05BB
Original Bad Block - 0:0x05C8
Original Bad Block - 0:0x05C9
Original Bad Block - 0:0x05CA
Original Bad Block - 0:0x05CB
Original Bad Block - 0:0x09F4
Original Bad Block - 0:0x09F5
Original Bad Block - 0:0x09F6
Original Bad Block - 0:0x09F7
Original Bad Block - 0:0x0C92
Original Bad Block - 0:0x0C93
Original Bad Block - 0:0x0C94
Original Bad Block - 0:0x0C95
Original Bad Block - 0:0x0C96
Original Bad Block - 0:0x0C97
Original Bad Block - 0:0x0C98
Original Bad Block - 0:0x0C99
Original Bad Block - 0:0x0C9A
Original Bad Block - 0:0x0C9B
Original Bad Block - 0:0x0ED8
Original Bad Block - 0:0x0ED9
Original Bad Block - 1:0x0000
Original Bad Block - 1:0x0D04
Original Bad Block - 1:0x0D05
Defect Table shows 8168 Good blocks, 32 Bad blocks
SafeErase (0,4100)
Erase failed Block - 0:0:0x0000
Erase failed Block - 0:0:0x000E
Erase failed Block - 0:0:0x000F
Erase failed Block - 0:0:0x00A8
Erase failed Block - 0:0:0x00A9
Erase failed Block - 0:0:0x022C
Erase failed Block - 0:0:0x022D
Erase failed Block - 0:0:0x05BA
Erase failed Block - 0:0:0x05BB
Erase failed Block - 0:0:0x05C8
Erase failed Block - 0:0:0x05C9
Erase failed Block - 0:0:0x05CA
Erase failed Block - 0:0:0x05CB
Erase failed Block - 0:0:0x09F4
Erase failed Block - 0:0:0x09F5
Erase failed Block - 0:0:0x09F6
Erase failed Block - 0:0:0x09F7
Erase failed Block - 0:0:0x0C92
Erase failed Block - 0:0:0x0C93
Erase failed Block - 0:0:0x0C94
Erase failed Block - 0:0:0x0C95
Erase failed Block - 0:0:0x0C96
Erase failed Block - 0:0:0x0C97
Erase failed Block - 0:0:0x0C98
Erase failed Block - 0:0:0x0C99
Erase failed Block - 0:0:0x0C9A
Erase failed Block - 0:0:0x0C9B
Erase failed Block - 0:0:0x0ED8
Erase failed Block - 0:0:0x0ED9
---> Max Bad of Plane (8,7)
SafeErase (1,4100)
Erase failed Block - 1:0:0x0000
Erase failed Block - 1:0:0x0D04
Erase failed Block - 1:0:0x0D05
---> Max Bad of Plane (1,1)
---> Max BAD/DIE = 8
Total good blocks after SCAN: 8168 / 8200, Bad block=32
==> 2-Plane mode
Max. Bad Block Allowed = 371(32)
Adjust Max LBA = 15646720, 15646656
MaxWindows=4/1910, MaxLBA=15646656, Size=7639 MB
Max BAD of one plane is 8 (46),8200,1,2
RootSector=0x1C53,Sec/Cluster=32, SuperPage=32 ---> Alignment=13
Boot Block=0x0001,0x0002
Lun0(14657648), Lun1(989008), Public=14657648, Secure=0, CDROM=989008
Special FE Config = 56-0B-00
Defect Table Block=0x0004
--- Download ISP Code:D:\MP_VER2162_ALL\ISP_CODE\6691_B3-A_20100331_VA10F00_9083.BIN---
--- ISP Code installed.
Lun0(14657648), Lun1(989008), Public=14657648, Secure=0, CDROM=989008
Public,Secure,CDROM = 14657648,0,989008
SN=003067830DE3F130ADC214DC
=== Preformat Done ===
Low Level Format DONE
Store INI/ERROR MSG to Block-0x0001:79.
### Err: CDROM file too large(00000000<000f1750).

Ending Time: 22:12:31

2011shazhou_li · 发表于 2011-3-10 22:21:08

现在连盘符都不出来啦

jjsfm · 发表于 2011-3-10 22:31:46

试试6692工具http://bbs.wuyou.net/forum.php?mod=viewthread&tid=180070
原配版本是V2.175；不出盘符可能要用短接法试试了。
先看看量产工具是否识别。。。。

2011shazhou_li · 发表于 2011-3-10 22:37:19

版主啊，我就是用Toshiba 43nm D2 的ini（带CDROM）的那个啊，出现了上面出错报告内容后，现在连盘符也出不来了。。。。。。

2011shazhou_li · 发表于 2011-3-10 22:51:42

谢谢啦，只能用短接法了，量产工具无法识别了！

2011shazhou_li · 发表于 2011-3-12 01:33:04

版主你好！
   现在盘符已经出来了！也下了6692工具，但那个INI文件不知道怎样修改啊，帮帮我吧，下面这个是我在量产前的信息备份：
MP Tool Version : V2.175
  INI File Name : 6692_CM_x2
  Format Date : 2010-12-25 15:17:29
  Flash Part No : Toshiba 3xnm D2 MLC
  CE-0, Flash ID=98-D7-94-32-76-55-0C
  CE-1, Flash ID=98-D7-94-32-76-55-0C
  VID : 0x0DD8
  PID : 0x1F08
  Vendor Name = Netac
  Product Name = OnlyDisk
  Serial Number = 001BFC6026F4FAC195912BF7
  Volume Label =
  F/W Version : 0xB5
  ISP Version : VB3.000B
  Flash R/W Timing : 33.3ns
  Channel : Byte Mode
  Homogeneous Mode : On
  HID Function : Disable
  Planes(F/W) : 1
  Pages/Block : 128 pages
  Max Current : 100 mA
  Total Blocks : 8200
  Bad Blocks : 32
  Capacity : 15595368 Sectors, 7984828416 Bytes
               7797684 KBytes, 7614.93 MBytes, 7.44 GBytes

2011shazhou_li · 发表于 2011-3-16 16:03:37

好久没做了，有点不死心！今天用MP_Ver2173再试了，提示错误代码25！
这个是我的配置文件：
[OEM]
PN=6692 + Toshiba 43nm D2 Normal Flash (CDROM)
Note=ISP:6692_B5-A_20100916_VB10000_63E2.BIN

VID=0x0DD8
PID=0x1F08
VENDOR_NAME="Netac"
PRODUCT_NAME="OnlyDisk"
STRING_DESC_ENABLE=1
SN_CustomerCode=0x0F

[FEATURE_SETTING]
FLASH_OP="ALL123"

ID17=1
ID35=1

[CDROM]
CDROM_ISO=F:\u\u.iso

[ISP]
Code=6692_B5-A_20100916_VB10000_63E2.BIN

下面是出错的报告：
tarting Time: 16:03:27

Device 1:0xB5
MP Version:2.173
INI_File_Name:6691_TSB_43nm_D2_CDROM.INI
Random delay 0 msec
--- Download MP ISP ---
CE-0, Flash ID=98-00-80-22-76-55-0C-02
CE-1, Flash ID=98-D7-94-32-76-55-0C-00
--> ROOT is not found
Scan (1,4100)
Original Defect Block - 1:0:0x0000
Original Defect Block - 1:0:0x0001
Original Defect Block - 1:0:0x0802
Original Defect Block - 1:0:0x0D04
Original Defect Block - 1:0:0x0D05
---> Max Bad of Plane (2,1)
---> Max BAD/DIE = 2
Total good blocks after SCAN: 4095 / 4100, Bad block=5
==> 2-Plane mode
MaxWindows=2/-56, MaxLBA=8187904, Size=3998 MB
Max BAD of one plane is 2 (1028),4100,1,1
RootSector=0xE19,Sec/Cluster=32, SuperPage=32 ---> Alignment=7
Boot Block=0x0001,0x0002
Lun0(7198896), Lun1(989008), Public=7198896, Secure=0, CDROM=989008
Special FE Config = 56-0B-00
Defect Table Block=0x0004
### Err: Preformat Abort ###
not enought block for d-block + min_algorithm_need
### Error: Low level format failed ###
Store INI/ERROR MSG to Block-0x0001:79.
SafeErase (1,4100)
Erase failed Block - 1:0:0x0000
Erase failed Block - 1:0:0x0001
Erase failed Block - 1:0:0x0802
Erase failed Block - 1:0:0x0D04
Erase failed Block - 1:0:0x0D05
---> Max Bad of Plane (2,1)
---> Max BAD/DIE = 2

Ending Time: 16:03:49
恳请高手指点！实在不死心啊。新朗科U208优盘，还没有使用就报废了！

jjsfm · 发表于 2011-3-16 16:53:23

是不是XP系统？

2011shazhou_li · 发表于 2011-3-16 22:35:55

是XP系统，现在问题得到解决，终于成功啦！谢谢司机啦。

nae_5288loveme · 发表于 2011-4-15 14:30:03

能给我你的配置表吗?我的也是朗科U208 8G的,跟你一样的芯片.拜托了!!

		自动登录	找回密码
密码			注册

菜鸟求救！朗科U208 8G求确认主控芯片方法

回复 #5 2011Hock 的帖子

回复 #12 jjsfm 的帖子