|
|
最近刷openwrt系统，结果变砖了，TTL还可以读取信息，ｕｂｏｏｔ进不去，ip地址浏览器也进不去，请大佬帮自己看看这个信息还有没有救？该怎么救？谢谢啦！有汉字部分是上面英文翻译过来的。
F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 0225 [010F]
Jump to BL
NOTICE: BL2: v2.6(release):
NOTICE: BL2: Built : 14:37:05, May 23 2022
NOTICE: WDT: disabled
NOTICE: CPU: MT7986 (1998MHz)
NOTICE: EMI: Using DDR3 settings
NOTICE: EMI: Detected DRAM size: 512MB
NOTICE: EMI: complex R/W mem test passed
NOTICE: SPI_NAND parses attributes from parameter page.
NOTICE: SPI_NAND Detected ID 0x75
NOTICE: Page size 2048, Block size 131072, size 134217728
NOTICE: Initializing NMBM ...
NOTICE: Signature found at block 1023 [0x07fe0000]
102B万
FA:1040000
FA:1040000[0200]
F9:0000
V0:0000(0001)
00:0000
BP:2400 0041[0000]
G0:1190万
EC:0000[1000]
T0:00000225[010F]
跳转到提单
注意:BL2:v2.6(release):
公告:BL2:建:2022年5月23日14:37:05
注意:WDT:禁用
注意:CPU:MT7986(1998MHz)
注意:EMI:使用DDR3设置
注意:EMI:检测DRAM大小:512MB
注意:EMI:复杂的R / W mem测试通过
注意:SPI_NAND解析参数页面的属性。
注意:SPI_NAND检测到ID 0x75
注意:页尺寸2048,块尺寸131072,尺寸134217728
注意:初始化NMBM…
注意:在1023街区(0x0770,0000)的签名
NOTICE: First info table with writecount 0 found in block 960
NOTICE: Second info table with writecount 0 found in block 963
NOTICE: NMBM has been successfully attached in read-only mode
NOTICE: BL2: Booting BL31
NOTICE: BL31: v2.6(release):
NOTICE: BL31: Built : 11:30:38, Jul 20 2022
U-Boot 2022.01-rc4-svn627 (Jul 20 2022 - 11:28:48 +0800)
CPU: MediaTek MT7986
Model: mt7986-rfb
DRAM: 512 MiB
Initializing NMBM ...
spi-nand: spi_nand spi_nand@1: Winbond SPI NAND was found.
spi-nand: spi_nand spi_nand@1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
Could not find a valid device for nmbm0
Signature found at block 1023 [0x07fe0000]
First info table with writecount 0 found in block 960
Second info table with writecount 0 found in block 963
NMBM has been successfully attached
MMC: mmc@11230000: 0
Loading Environment from MTD... *** Warning - bad CRC, using default
注意:第一个信息表与第960块中发现的writecount 0
注意:第963块中发现的第一个信息表
注意:NMBM已成功地连接到只读模式
注意:BL2:Booting BL31
注意:BL31:v2.6(release):
注意:BL31:建造:11:30:38,Jul 20 2022
U-Boot 2022.01-rc4-svn627(Jul 20 2022 - 11:28 48 + 0800)
CPU:MediaTek MT7986
型号:mt7986-rfb
DRAM:512 MiB
初始化NMBM…
spinand:spi_nand spi_nand@1:Winbond SPI NAND被发现。
spinand:spi_nand spi_nand@1:128 MiB,块大小:128 KiB,页大小:2048,OOB大小:64
无法找到nmbm0的有效设备
第1023章[0x0707]的签名
第一个信息表与第960块中发现的writecount
第二个信息表,在第963块中发现了writecount
NMBM已成功连接
MMC:mmc@11230000:0
从MTD加载环境…* * *警告-糟糕的CRC,使用默认
environment
In: serial@11002000
Out: serial@11002000
Err: serial@11002000
Net:
Warning: ethernet@15100000 (eth0) using random MAC address - 16:2d:b8:5d:54:2f
eth0: ethernet@15100000
*** U-Boot Boot Menu ***
1. Startup system (Default)
2. Upgrade firmware
3. Upgrade ATF BL2
4. Upgrade ATF FIP
5. Upgrade single image
6. Load image
0. U-Boot console
Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
ubi0: attaching mtd8
ubi0: scanning is finished
ubi0: attached mtd8 (name "ubi", size 63 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
环境
正文:serial@11002000
Out:serial@11002000
错误:serial@11002000
网:
警告:ethernet@15100000(eth0)使用随机MAC地址- 16:2d:b8:5d:54:2f
eth0:ethernet@15100000
* * * u -引导引导菜单* * *
1 .工作启动系统(默认)
二。升级固件
3 .工作升级ATF BL2
4。升级ATF FIP
5。升级单映像
6。负载图象
0。U-Boot控制台
按下/向下移动,输入选择,ESC / CTRL + C退出
ubi0:附加mtd8
结果:扫描完成
ubi0:附件mtd8(名称为ubi,尺寸63 MiB)
ubi0:PEB size:131072字节(128 KiB),LEB大小:126976字节
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 504, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 16/5, WL threshold: 4096, image sequence number: 982326636
ubi0: available PEBs: 0, total reserved PEBs: 504, PEBs reserved for bad PEB handling: 19
Reading from volume 'kernel' to 0x46000000, size 0x0 ... OK
## Loading kernel from FIT Image at 46000000 ...
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-6.6.74
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x460000e8
Data Size: 4407459 Bytes = 4.2 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x48000000
Entry Point: 0x48000000
Hash algo: crc32
Hash value: 31542afe
Hash algo: sha1
Hash value: c584254b57b5da94d6c077994fede1a23f2884a2
Verifying Hash Integrity ... crc32+ sha1+ OK
ubi0:min.max。I / O单位尺寸:2048 / 2048,分页尺寸2048
结果头偏移:2048(对齐2048),数据偏移量:4096
ubi0:good PEBs:504,bad PEBs:0,rot PEBs:0
ubi0:用户音量:3,内部音量:1,max。数量:128
ubi0:max / mean擦除计数器:16/5,WL阈值:4096,图像序列号:982326636
ubi0:可用的PEBs:0,总保留的PEBs:504,PEB处理的PEBs:19
从体积内核到0x46000000,大小0x0…好的
# # #加载内核从FIT图像达到46000000…
使用“config-1”配置
尝试“kernel - 1”核子映像
描述:ARM64 OpenWrt linux 6.6.6.6.74
类型:内核映像
压缩:lzma压缩
数据开始:0x460000e8
数据大小:4407459字节= 4.2 MiB
建筑:AArch64
操作系统:Linux
负载地址:0x48000000
入口点:0x48000000
哈希·阿尔戈:crc32
哈希值:31542afe
哈希·阿尔戈:sha1
哈希值:c584254b57b5da94d6c077994fede1a23f2884a2
验证哈希完整性…crc32 + sha1 + OK
## Loading fdt from FIT Image at 46000000 ...
Using 'config-1' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt ruijie_rg-x60-pro device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x464342d0
Data Size: 20148 Bytes = 19.7 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: cb9666c5
Hash algo: sha1
Hash value: 011c6c009c0ea59708140abef70d83164605b1bc
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x464342d0
Uncompressing Kernel Image
Loading Device Tree to 000000005f7f1000, end 000000005f7f8eb3 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.6.74 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28694-730db6b893) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Sun Jan 26 00:17:11 2025
[ 0.000000] Machine model: Ruijie RG-X60 Pro
[ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '')
# #加载fdt从FIT图像达到46000000…
使用“config-1”配置
尝试fds - 1 ' fdt subimage
描述:ARM64 OpenWrt rui - x60 pro设备树blob
类型:平板设备树
压缩:未压缩
数据开始:0x464342d0
数据大小:20148字节= 19.7 KiB
建筑:AArch64
哈希·阿尔戈:crc32
哈希值:cb9666c5
哈希·阿尔戈:sha1
哈希值:011c6c6c0ea59708140abef70d83164605b1bc
验证哈希完整性…crc32 + sha1 + OK
使用fdt blob在0x464342d0中启动
未压缩核象
装载设备树到00005f7f1000,end 00005f7f8eb3…好的
启动内核…
[0.000000]启动Linux物理CPU 0x0000000000[0x410fd034]
[60000]Linux版本6.74(builder@buildhost)(aarch64 OpenWrt - Linux - musl - GCC)
[0.000000]机器型号:瑞杰rs - x60 Pro
[0.000000]earlycon:uart8250在MMIO32 0x000011002000(选项”)
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] OF: reserved mem: 0x0000000042ff0000..0x0000000042ffffff (64 KiB) map non-reusable ramoops@42ff0000
[ 0.000000] OF: reserved mem: 0x0000000043000000..0x000000004302ffff (192 KiB) nomap non-reusable secmon@43000000
[ 0.000000] OF: reserved mem: 0x000000004fc00000..0x000000004fcfffff (1024 KiB) nomap non-reusable wmcpu-reserved@4fc00000
[ 0.000000] OF: reserved mem: 0x000000004fd00000..0x000000004fd3ffff (256 KiB) nomap non-reusable wo-emi@4fd00000
[ 0.000000] OF: reserved mem: 0x000000004fd40000..0x000000004fd7ffff (256 KiB) nomap non-reusable wo-emi@4fd40000
[ 0.000000] OF: reserved mem: 0x000000004fd80000..0x000000004ffbffff (2304 KiB) nomap non-reusable wo-data@4fd80000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000005fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
[ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff]
[ 0.000000] node 0: [mem 0x0000000043030000-0x000000004fbfffff]
[ 0.000000] node 0: [mem 0x000000004fc00000-0x000000004ffbffff]
[ 0.000000] node 0: [mem 0x000000004ffc0000-0x000000005fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[0.000000]printk:bootconsole[uart8250]启用
[0.000000]:预留mem:0x000042ff0000。0x000042ffffff(64 KiB)map不可重用的ramoops@42ff0000
[0.000000]:预留mem:0x0000430000000x00004302ffff(192 KiB)nomap不可复用secmon@4000000
[0.000000]:预留mem:0x00004fc000000x00004ffffff(1024 KiB)nomap不可重复使用的wmcpureserved@4fc00000
[0.000000]:预留mem:0x00004fd000000x00004fd3ffff(256 KiB)nomap不可重复使用的wo-emi@4fd00000
[0.000000]:预留mem:0x00004fd400000x00004fd7ffff(256 KiB)nomap不可重用的wo-emi@4fd40000
[0.000000]:预留mem:0x00004fd800000x00004ffbffff(2304 KiB)nomap不可重用的wo-data@4fd80000
[0.000000]区域范围:
[000000]DMA[mem 0x000000004000x00005fffffff]
[0.000000]DMA32空
[0.000000]正常空
[0.000000]可移动区开始为每个节点
[0.000000]早期记忆节点范围
[0.000000]节点0:[mem 0x0000000000000000x000042ffffffff]
[0.000000]节点0:[mem 0x00000000430000000x00004302ffff]
[0.000000]节点0:[mem 0x0000000043030000 - 0x00004fbfffff]
[0.000000]节点0:[mem 0x000000004fc000x00004ffbffff]
[0.000000]节点0:[mem 0x000000004ffc00000x00005fffffff]
[0.000000]Initmem设置节点0[mem 0x000000004000x00005fffffffff]
[0.000000]psci:从DT探测管道方法。
[0.000000]psci:固件中检测到的PSCIv1.1。
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 18 pages/cpu s35560 r8192 d29976 u73728
[ 0.000000] pcpu-alloc: s35560 r8192 d29976 u73728 alloc=18*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon=uart8250,mmio32,0x11002000
[ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129024
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 0MB
[ 0.000000] software IO TLB: area num 4.
[ 0.000000] software IO TLB: SWIOTLB bounce buffer size roundup to 1MB
[ 0.000000] software IO TLB: mapped [mem 0x000000005fcc7000-0x000000005fdc7000] (1MB)
[ 0.000000] Memory: 495180K/524288K available (9024K kernel code, 1000K rwdata, 2620K rodata, 448K init, 307K bss, 29108K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[0.000000]psci:使用标准psci v0.2功能id
[0.000000]psci:不支持迁移信息_type。
[0.30]psci:SMC call公约v1.2
[0.30]
[000000]pcpuofc:s35560 r8192 d29976 u73728
[0][0][0][0]2[0]3
[0.000000]在CPU0上检测到VIPT I-cache
[0.000000]CPU特性:检测:GIC系统注册CPU接口
[0.000000]CPU特性:内核页表隔离,由内核配置禁用
[0.000000]选择:应用引导替代方案
[000000]内核命令行:控制台= ttyS0,115200n8 earlycon = uart8250,mmio32,0x11002000
[0.000000]Dentry缓存哈希表条目:65536(订单:7,524288字节,线性)
[0.000000]inodecache哈希表条目:32768(订单:6,262144字节,线性)
[0.000000]建立1个zonelists,移动分组。总页数:129024
[000000]mem自动init:stack:off,heap alloc:off,heap free:off
[000000]软件IO TLB:SWIOTLB反弹缓冲区大小调整为0MB
[0.000000]软件IO TLB:num 4。
[000000]软件IO TLB:SWIOTLB反弹缓冲大小对1MB
[000000]软件IO TLB:映射[mem 0x000000005fcc7000 - x00005fdc7000](1MB)
[0.000000]内存:495180K / 524288K(9024K内核代码,1000K rwdata,2620K rodata,448K init,307K bss,29108K保留,0K cma保留)
[0.000000](0 - 3,minobject = 0,CPUs = 4,节点= 1)
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 640 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv3: GICv3 features: 16 PPIs
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[ 0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[ 0.008117] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000)
[ 0.018520] pid_max: default: 32768 minimum: 301
[ 0.025117] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.032464] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.041763] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.048281] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[0.000000]rcu:分级rcu实现。
[0.000000]跟踪RCU启用任务的变体。
[0.000000]rcu:rcu计算的调度延迟延迟的值为10个。
[0.10]NR_IRQS:64,NR_IRQS:64,预分配的irqs:0
[0.000000]GICv3:GIC:使用拆分EOI / deactive模式
[0.000000]GICv3:640 SPIs实现
[0.000000]GICv3:0扩展SPIs实现
[0.000000]根IRQ处理程序:gic_handle_irq
[0.000000]GICv3特性:16 PPIs
[0.000000]GICv3:CPU0:发现分销商0区域0:0:0:0:0:0000c080000
srcu_init:基于争用设置srcu_struct大小。
[0.000000]arch_timer:cp15计时器在13.00MHz(phys)运行。
[0.000000]
[0.000000]sched_clock:56位在13MHz,分辨率76ns,每4398046511101ns
[0.008117]校准延迟循环(省略),使用计时器频率计算的值。2 . BogoMIPS(lpj = 130000)
[0.018520]pid_max:默认:32768最小:301
[0.025117]Mount-cache分类表条目:1024(订单:1,8192字节,线性)
[0.032464]mountpoint -缓存哈希表条目:1024(订单:1,8192字节,线性)
[0.041763]cacheinfo:无法检测CPU 0的缓存层次
RCU任务跟踪:设置向2和lim到1 rcu_task_cb_debug = 1 rcu_task_cpu_ids = 4。
[ 0.057643] rcu: Hierarchical SRCU implementation.
[ 0.062454] rcu: Max phase no-delay instances is 1000.
[ 0.068012] smp: Bringing up secondary CPUs ...
[ 0.072828] Detected VIPT I-cache on CPU1
[ 0.072862] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[ 0.072888] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.073172] Detected VIPT I-cache on CPU2
[ 0.073191] GICv3: CPU2: found redistributor 2 region 0:0x000000000c0c0000
[ 0.073202] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.073465] Detected VIPT I-cache on CPU3
[ 0.073482] GICv3: CPU3: found redistributor 3 region 0:0x000000000c0e0000
[ 0.073491] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.073518] smp: Brought up 1 node, 4 CPUs
[ 0.130051] SMP: Total of 4 processors activated.
[ 0.134771] CPU features: detected: 32-bit EL0 Support
[ 0.139926] CPU features: detected: CRC32 instructions
[ 0.145105] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.153491] CPU: All CPU(s) started at EL2
[ 0.157601] alternatives: applying system-wide alternatives
[ 0.165687] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.175584] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.183352] pinctrl core: initialized pinctrl subsystem
[0.057643]rcu:分级SRCU实现。
[0.062454]rcu:最大阶段无延迟实例是1000。
[0.068012]smp:引入二次cpu…
[0.072828]在CPU1上检测到VIPT I-cache
[0.072862]GICv3:CPU1:发现分销商1区域0:0:0:0:0000c0a0000
[0.072888]CPU1:引导二次处理器0x0000000001[0x410fd034]
[0.073172]在CPU2上检测到VIPT I-cache
[0.073191]GICv3:CPU2:发现re分销商2区域0:0x000000c0000
[0.073202]CPU2:启动二次处理器0x0000000002[0x410fd034]
[0.073465]在CPU3上检测到VIPT I-cache
[0.073482]GICv3:CPU3:发现分销商3区域0:0x000000000c0000
[0.073491]CPU3:引导二次处理器0x0000000003[0x410fd034]
[0.073518]smp:增加1节点,4个cpu
[0.130051]SMP:共激活4个处理器。
[0.134771]CPU特性:检测:32位EL0支持
[0.139926]CPU特性:检测:CRC32指令
[0.145105]CPU特性:模拟:使用TTBR0_EL1切换的特权访问
[0.153491]CPU:所有CPU(s)从EL2开始
[0.157601]选择:应用全系统替代方案
[0.165687]存条来源:jifface:0xffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff@@
[0.175584]futex . hash表项:1024(订单:4,65536字节,线性)
[0.183352]pinctrl核心:初始化pinctrl子系统
[ 0.189401] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.195585] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.202690] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.210478] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.218711] thermal_sys: Registered thermal governor 'fair_share'
[ 0.218714] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.224830] thermal_sys: Registered thermal governor 'step_wise'
[ 0.230864] thermal_sys: Registered thermal governor 'user_space'
[ 0.236939] ASID allocator initialised with 65536 entries
[ 0.249158] pstore: Using crash dump compression: deflate
[ 0.254582] pstore: Registered ramoops as persistent store backend
[ 0.260786] ramoops: using 0x10000@0x42ff0000, ecc: 0
[ 0.266586] /soc/interrupt-controller@c000000: Fixed dependency cycle(s) with /soc/interrupt-controller@c000000
[ 0.280683] Modules: 29376 pages in range for non-PLT usage
[ 0.280693] Modules: 520896 pages in range for PLT usage
[ 0.287076] cryptd: max_cpu_qlen set to 1000
[ 0.297395] SCSI subsystem initialized
[ 0.301225] libata version 3.00 loaded.
[ 0.306051] clocksource: Switched to clocksource arch_sys_counter
[ 0.313787] NET: Registered PF_INET protocol family
[ 0.318795] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.327070] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[0.189401]网络:注册PF_NETLINK / PF_ROUTE协议家庭
[0.195585]DMA:预分配128 KiB GFP_KERNEL池进行原子分配
[0.202690]DMA:预分配128 KiB GFP_KERNEL | GFP_DMA池进行原子分配
[0.210478]DMA:预分配128 KiB GFP_KERNEL | GFP_DMA32池进行原子分配
[0.218711]thermal_sys:注册热调节器“fair_share”
[0.218714]thermal_sys:注册热调速器' bang_bang '
[0.224830]thermal_sys:注册热调节器“step_wise”
[0.230864]thermal_sys:注册热调节器“user_space”
[0.236939]ASID allocator初始化65536项
[0.249158]pstore:使用崩溃转储压缩
[0.254582]pstore:注册ramoops为持久性存储后端
[0.260786]ramoops:使用0x10000@0x42ff0000,ecc:0
[0.266586]/ soc /中断-控制器@ c000000:固定依赖周期(s)
[0.280683]模块:376页,适用于非plt使用范围
[0.280693]模块:520896页,适用于PLT使用范围
[0.287076]cryptd:max_cpu_qlen设置为1000
[0.297395]SCSI子系统初始化
[0.301225]libata版本3.00加载。
[0.306051]时钟源:切换到时钟源arch_sys_counter
[0.313787]网:注册PF_INET协议家族
[0.318795]IP idents哈哈表条目:8192(订单:4,65536字节,线性)
[0.327070]tcp_portaddr_hash表条目:256(order:0,4096字节,线性)
[ 0.335465] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.343250] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.351047] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 0.358399] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.365012] MPTCP token hash table entries: 512 (order: 1, 12288 bytes, linear)
[ 0.372424] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.378991] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.386210] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.391920] PCI: CLS 0 bytes, default 64
[ 0.396879] workingset: timestamp_bits=46 max_order=17 bucket_order=0
[ 0.406676] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.412535] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.443814] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.454686] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.464193] printk: console [ttyS0] disabled
[ 0.488874] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 116, base_baud = 2500000) is a ST16650V2
[ 0.498174] printk: console [ttyS0] enabled
[ 0.498174] printk: console [ttyS0] enabled
[ 0.506526] printk: bootconsole [uart8250] disabled
[ 0.506526] printk: bootconsole [uart8250] disabled
[ 0.519685] loop: module loaded
[0.335465]表- perturb哈希表条目:65536(订单:6,262144字节,线性)
[0.343250]TCP创建的哈希表条目:4096(订单:3,32768字节,线性)
[0.351047]TCP绑定哈希表条目:4096(订单:5,131072字节,线性)
[0.358399]TCP:配置的哈希表(建立4096绑定4096)
[0.365012]MPTCP令牌哈希表条目:512(订单:1,12288字节,线性)
[0.372424]UDP哈希表条目:256(订单:1,8192字节,线性)
[0.378991]UDP-Lite哈希表条目:256(订单:1,8192字节,线性)
[0.386210]网:注册PF_UNIX / PF_LOCAL协议
[0.391920]PCI:CLS 0字节,默认64
[0.396879]workingset:timestamp_bits = 46 max_order = 17
[0.406676]squashfs:版本4.0(2009/01/31)
[0.412535]jffs2:版本2.2(NAND)(摘要)(LZMA)(rzma)(CMODE_PRIORITY)2001-2006年Red Hat,Inc .。
[0.443814]Block layer SCSI通用(bsg)驱动版本0.4加载(主要251)
[0.454686]串行:8250/16550驱动程序,16个端口,IRQ共享启用
[0.464193]printk:控制台[ttyS0]禁用
[0.488874]11002000。串行:ttyS0在MMIO 0x11002000(irq = 116,base_baud = 2500000)是ST16650V2
[0.498174]printk:控制台[ttyS0]启用
[0.498174]printk:控制台[ttyS0]启用
[0.506526]printk:禁用bootconsole[uart8250]禁用
[0.506526]printk:禁用bootconsole[uart8250]禁用
[0.519685]循环:加载模块
[ 0.524261] spi-nand spi0.0: Winbond SPI NAND was found.
[ 0.529600] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 0.538195] Signature found at block 1023 [0x07fe0000]
[ 0.543319] NMBM management region starts at block 960 [0x07800000]
[ 0.551053] First info table with writecount 0 found in block 960
[ 0.561540] Second info table with writecount 0 found in block 963
[ 0.567711] NMBM has been successfully attached
[ 0.572505] 7 fixed-partitions partitions found on MTD device spi0.0
[ 0.578860] Creating 7 MTD partitions on "spi0.0":
[ 0.583635] 0x000000000000-0x000000100000 : "BL2"
[ 0.589353] 0x000000100000-0x000000180000 : "u-boot-env"
[ 0.595255] 0x000000180000-0x000000380000 : "Factory"
[ 0.602081] 0x000000380000-0x000000580000 : "FIP"
[ 0.608443] 0x000000580000-0x000000600000 : "product_info"
[ 0.614540] 0x000000600000-0x000000680000 : "kdump"
[ 0.620038] 0x000000680000-0x000004580000 : "ubi"
[ 0.797303] mtk_soc_eth 15100000.ethernet: generated random MAC address 65:74:68:25:64:00
[ 0.805480] mtk_soc_eth 15100000.ethernet: generated random MAC address 65:74:68:25:64:00
[ 1.179383] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc081680000, irq 120
[ 1.189254] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc081680000, irq 120
[ 1.198925] i2c_dev: i2c /dev entries driver
[ 1.204441] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[0.524261]spinand spi0.0:Winbond SPI NAND。
[0.529600]spinand spi0.0:128 MiB,块大小:128 KiB,页大小:2048,OOB大小:64
[0.538195]在1023街区(0x0770,0000)找到的签名
[0.543319]NMBM管理区域从960街区开始[0x7800000]
[0.551053]第一个信息表,在960街区发现的writecount
[0.561540]第963号writecount 0的第二次信息表
[0.567711]NMBM已成功连接
[0.572505]MTD设备发现的7个固定分区分区
[0.578860]在“spi0.0”上创建7个MTD分区:
[0.583635]0x000000000x000000100000:“BL2”
[0.589353]0x0000000x000000180000:" u-boot-env "
[0.595255]0x0000000x000000380000:“工厂”
[0.602081]0x0000000x000000580000:“FIP”
[0.608443]0x0000000x0000600000:“product_info”
[0.614540]0x0000000x000000680000:“kdump”
[0.620038]0x0000000x000004580000:“ubi”
[0.797303]mtk_soc_eth 1510万。以太网:生成的随机MAC地址
[0.805480]mtk_soc_eth 1510万。以太网:生成的随机MAC地址
[1.179383]mtk_soc_eth 1510万。以太网eth0:mediatek框架引擎在0xffffffffffffffffffc081680000,irq 120
[1.189254]mtk_soc_eth 1510万。以太网eth1:mediatek框架引擎在0xffffffffffffc081680000,irq 120
[1.198925]i2c_dev:i2c / dev条目驱动程序
[1.204441]mtk-wdt 1001c000。看门狗:看门狗(超时= 31秒,nowatry = 0)
[ 1.213316] NET: Registered PF_INET6 protocol family
[ 1.219131] Segment Routing with IPv6
[ 1.222806] In-situ OAM (IOAM) with IPv6
[ 1.226776] NET: Registered PF_PACKET protocol family
[ 1.231836] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.244964] 8021q: 802.1Q VLAN Support v1.8
[ 1.332122] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x link mode
[ 1.341087] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 1.351817] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7531 PHY] (irq=124)
[ 1.374527] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=125)
[ 1.396510] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=126)
[ 1.418425] mt7530-mdio mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=127)
[ 1.429818] mtk_soc_eth 15100000.ethernet eth0: entered promiscuous mode
[ 1.436534] DSA: tree 0 setup
[ 1.440080] UBI: auto-attach mtd6
[ 1.443388] ubi0: default fastmap pool size: 25
[ 1.447910] ubi0: default fastmap WL pool size: 12
[ 1.452683] ubi0: attaching mtd6
[ 1.790095] ubi0: scanning is finished
[ 1.801303] ubi0 warning: ubi_eba_init: cannot reserve enough PEBs for bad PEB handling, reserved 17, need 19
[1.213316]网络:注册PF_INET6协议家庭
[1.219131]段路由与IPv6
[1.222806]使用IPv6原位OAM(IOAM)
[1.226776]网:注册pf_数据包协议家庭
[1.231836]桥梁:通过arp / ip / ip6tables进行过滤,默认情况下不再可用。如果需要,更新脚本来加载br_netfilter。
[1.244964]8021q:802.1Q VLAN支持v1.8
[1.332122]mt7530-mdio mdio-bus:1f:配置固定/ 2500base-x链路模式
[1.341087]mt7530-mdio mdio-bus:1f:Link Up - 2.5Gbps / Full - flow control rx / tx
[1.351817]mt7530-mdio mdio-bus:1f lan1(未初始初始):PHY[mt7530-0:00]驱动[MediaTek MT7531 PHY](irq = 124)
[1.374527]mt7530-mdio mdio-bus:1f lan2(未初始初始):PHY[mt7530-0:01]驱动[MediaTek MT7531 PHY](irq = 125)
[1.396510]mt7530-mdio mdio-bus:1f lan3(未初始初始):PHY[mt7530-0:02]驱动[MediaTek MT7531 PHY](irq = 126)
[1.418425]mt7530-mdio mdio-bus:1f lan4(未初始初始):PHY[mt7530-0:03]驱动[MediaTek MT7531 PHY](irq = 127)
[1.429818]mtk_soc_eth 1510万。以太网eth0:输入滥交模式
[1.436534]DSA:树0设置
[1.440080]UBI:自动附加mtd6
[1.443388]ubi0:默认的fastmap池大小:25
[1.447910]ubi0:默认fastmap WL池大小:12
[1.452683]ubi0:附加mtd6
[1.790095]ubi0:扫描完成
[1.801303]ubi0警告:ubi_eba_init:不能保留足够的PEB处理,保留17,需要19
[ 1.811617] ubi0: attached mtd6 (name "ubi", size 63 MiB)
[ 1.817014] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.823868] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.830636] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.837578] ubi0: good PEBs: 504, bad PEBs: 0, corrupted PEBs: 0
[ 1.843564] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 1.850765] ubi0: max/mean erase counter: 16/5, WL threshold: 4096, image sequence number: 982326636
[ 1.859874] ubi0: available PEBs: 0, total reserved PEBs: 504, PEBs reserved for bad PEB handling: 17
[ 1.869077] ubi0: background thread "ubi_bgt0d" started, PID 632
[ 1.875800] block ubiblock0_1: created from ubi0:1(rootfs)
[ 1.881287] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 1.888305] clk: Disabling unused clocks
[ 1.898405] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 1.905723] Freeing unused kernel memory: 448K
[ 1.910210] Run /sbin/init as init process
[ 1.914290] with arguments:
[ 1.917247] /sbin/init
[ 1.919939] with environment:
[ 1.923063] HOME=/
[ 1.925407] TERM=linux
[ 2.098504] init: Console is alive
[1.811617]ubi0:附件mtd6(名称为ubi,尺寸63 MiB)
[1.817014]ubi0:PEB size:131072字节(128 KiB),LEB大小:126976字节
[1.823868]ubi0:min.max。I / O单位尺寸:2048 / 2048,分页尺寸2048
[1.830636]ubi0:VID头偏移量:2048(对齐2048),数据偏移量:4096
[1.837578]ubi0:good PEBs:504,bad PEBs:0,损坏的PEBs:0
[1.843564]ubi0:用户音量:3,内部音量:1,max。数量:128
[1.850765]ubi0:max / mean擦除计数器:16/5,WL阈:4096,图像序列号:982326636
[1.859874]ubi0:可用的PEBs:0,总保留PEBs:504,pbs保留为坏PEB处理:17
[1.869077]ubi0:背景线“ubi_bgt0d”开始,PID 632
[1.875800]ubiblock0_1:从ubi0:1创建(rootfs)
[1.881287]ubiblock:设备ubiblock0_1(rootfs)集为根文件系统
[1.888305]clk:禁用未使用的时钟
[1.898405]VFS:安装在设备254:0上的安装根(squashfs文件系统)。
[1.905723]释放未使用的内核内存:448K
[1.910210]运行/sbin/init为init进程
[1.914290]论点:
[1.917247]/sbin/init
[1.919939]与环境:
[1.923063]
[1.925407]学期= linux
[2.098504)init:控制台还活着
[ 2.102004] init: - watchdog -
[ 2.424990] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.449969] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 2.459027] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 2.467868] init: - preinit -
[ 2.749412] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 2.757873] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 2.776268] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 7.013441] UBIFS (ubi0:2): Mounting in unauthenticated mode
[ 7.019169] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 769
[ 7.061046] UBIFS (ubi0:2): recovery needed
[ 7.096059] random: crng init done
[ 7.181447] UBIFS (ubi0:2): recovery completed
[ 7.185933] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 7.193752] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 7.203645] UBIFS (ubi0:2): FS size: 50409472 bytes (48 MiB, 397 LEBs), max 407 LEBs, journal size 2539520 bytes (2 MiB, 20 LEBs)
[ 7.215272] UBIFS (ubi0:2): reserved for root: 2380963 bytes (2325 KiB)
2.102004]init:-看门
[2.424990]kmodloader:从/ etc/模块化- boot.d / *加载内核模块
[2.449969]gpio_button_hotplug:加载下树模块隔离内核。
[2.459027]kmodloader:完成从/ etc/模块化- boot.d / *加载内核模块
[2.467868]init:- preinit -
[2.749412]mtk_soc_eth 1510万。以太网eth0:配置固定/ 2500base-x链路模式
[2.757873]mtk_soc_eth 1510万。以太网eth0:Link是Up - 2.5Gbps / Full - flow control rx / tx
[2.776268]mt7530-mdio mdio-bus:1f lan1:对phy / gmii链路模式的配置
按[f]键,击[输入]进入故障安全模式
按[1]、[2]、[3]或[4]键,点击[输入],选择调试级别
[7.013441]UBIFS(ubi0:2):未经认证模式安装
[7.019169]UBIFS(ubi0:2):背景线程“ubifs_bgt0_2”启动,PID 769
[7.061046]UBIFS(ubi0:2):需要恢复
随机的:crng init完成
[7.181447]UBIFS(ubi0:2):恢复完成
UBIFS:UBIFS:UBIFS:安装UBI设备0,第2卷,名称“rootfs_data”
[7.193752]UBIFS(ubi0:2):LEB size:126976字节(124 KiB),min.max。I / O单位尺寸:2048字节/ 2048字节
[7.203645]UBIFS:FS size:50409472字节(48 MiB,397 LEBs),max 407 LEBs,journal size 2539520字节(2 MiB,20个LEBs)
[7.215272]UBIFS(ubi0:2):预留为根:2380963字节(2325 KiB)
[ 7.221870] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID B5514430-4499-427F-AF04-B77FB89D2B2D, small LPT model
[ 7.238031] mount_root: switching to ubifs overlay
[ 7.246756] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[ 7.263088] urandom-seed: Seeding with /etc/urandom.seed
[ 7.307989] procd: - early -
[ 7.310915] procd: - watchdog -
[ 7.844104] procd: - watchdog -
[ 7.892615] procd: - ubus -
[ 8.045797] procd: - init -
Please press Enter to activate this console.
[ 8.329934] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.364235] Loading modules backported from Linux version v6.12.6-0-ge9d65b48ce1a
[ 8.371721] Backport generated by backports.git v6.1.110-1-35-g410656ef04d2
[ 8.465442] urngd: v1.0.2 started.
[ 8.729768] mt798x-wmac 18000000.wifi: HW/SW Version: 0x8a108a10, Build Time: 20240823160656a
[ 8.729768]
[ 8.909966] mt798x-wmac 18000000.wifi: WM Firmware Version: ____000000, Build Time: 20240823160721
[ 9.004289] mt798x-wmac 18000000.wifi: WA Firmware Version: DEV_000000, Build Time: 20240823160840
[ 9.110687] mt798x-wmac 18000000.wifi: registering led 'mt76-phy0'
[ 9.157579] mt798x-wmac 18000000.wifi: registering led 'mt76-phy1'
[ 9.233260] mtdblock: MTD device 'product_info' is NAND, please consider using UBI block devices instead.
UBIFS(ubi0:2):媒体格式:w5 / r0(最新is w5 / r0),uuuid b551444 - 4499 - 427f - af04 - b89d2b2d,小型LPT模型
[7.238031]mount_root:切换到ubifs覆盖
[7.246756]overlayfs:在小写fs ' / '中检测到null uuid,返回xino = off,index = off,nfs_export = off。
[7.263088]urandom种子:播种与/etc/urandom.seed
[7.307989]procd:-早期
[7.310915]procd:-看门
[7.844104]procd:-监督-
[7.892615]procd:- ubus
[8.045797]procd:- init -
请按Enter激活这个控制台。
[8.329934]kmodloader:从/ etc /模块化中加载内核模块
从Linux版本v6.12.6-0-ge9d65b48ce1a返回的加载模块
[8.371721]Backport生成的Backport。g410656ef04d2
[8.465442]urngd:v1.0.2启动。
[8.729768]mt798x-wmac 18000000。wifi:HW / SW版本:0x8a108a10,建造时间:20240823160656a
[8.729768]
[8.909966]mt798x-wmac 18000000。wifi:WM固件版本:ec000000,内置时间:20240823160721
[9.07]mt798x-wmac 18000000。wifi:WA固件版本:DEV_000000,构建时间:20240823160840
[9.110687]mt798x-wmac 18000000。wifi:注册led ' mt76-phy0 '
[9.157579]mt798x-wmac 18000000。wifi:注册led ' mt76-phy1 '
[9.233260]mtdblock:MTD设备的“product_info”是NAND,请考虑使用UBI屏蔽设备。
[ 9.246481] PPP generic driver version 2.4.2
[ 9.251505] NET: Registered PF_PPPOX protocol family
[ 9.258699] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 9.819293] mtdblock: MTD device 'product_info' is NAND, please consider using UBI block devices instead.
[ 11.437519] mtk_soc_eth 15100000.ethernet eth0: Link is Down
[ 11.452893] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 11.461336] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 11.468086] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 11.481018] br-lan: port 1(lan1) entered blocking state
[ 11.486264] br-lan: port 1(lan1) entered disabled state
[ 11.491499] mt7530-mdio mdio-bus:1f lan1: entered allmulticast mode
[ 11.497760] mtk_soc_eth 15100000.ethernet eth0: entered allmulticast mode
[ 11.507239] mt7530-mdio mdio-bus:1f lan1: entered promiscuous mode
[ 11.524183] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 11.534926] br-lan: port 2(lan2) entered blocking state
[ 11.540212] br-lan: port 2(lan2) entered disabled state
[ 11.545458] mt7530-mdio mdio-bus:1f lan2: entered allmulticast mode
[ 11.553493] mt7530-mdio mdio-bus:1f lan2: entered promiscuous mode
[ 11.567532] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 11.578211] br-lan: port 3(lan3) entered blocking state
[ 11.583436] br-lan: port 3(lan3) entered disabled state
[9.246481]PPP通用驱动版2.4.2
[9.251505]网:注册PF_PPPOX协议家庭
[9.258699]kmodloader:完成从/ etc /模块化加载内核模块
[9.819293]mtdblock:MTD设备的“product_info”是NAND,请考虑使用UBI屏蔽设备。
[11.437519]mtk_soc_eth 1510万。以太网eth0:链接向下
[11.452893]mtk_soc_eth 1510万。以太网eth0:配置固定/ 2500base-x链路模式
[11.461336]mtk_soc_eth 1510万。以太网eth0:Link是Up - 2.5Gbps / Full - flow control rx / tx
[11.468086]mt7530-mdio mdio-bus:1f lan1:对phy / gmii链路模式的配置
[11.481018]brlan:端口1(lan1)进入阻塞状态
[11.486264]brlan:端口1(lan1)进入禁用状态
[11.491499]mt7530-mdio mdio-bus:1f lan1:输入allmultiast模式
[11.497760]mtk_soc_eth 1510万。以太网eth0:输入allmultiast模式
[11.507239]mt7530-mdio mdio-bus:1f lan1:输入杂乱模式
[11.524183]mt7530-mdio mdio-bus:1f lan2:对phy / gmii链路模式的配置
[11.534926]brlan:端口2(lan2)进入阻塞状态
[11.540212]brlan:port 2(lan2)进入禁用状态
[11.545458]mt7530-mdio mdio-bus:1f lan2:输入allmultiast模式
[11.553493]mt7530-mdio mdio-bus:1f lan2:输入滥运模式
[11.567532]mt7530-mdio mdio-bus:1f lan3:配置phy / gmii链路模式
[11.578211]brlan:端口3(lan3)进入阻塞状态
[11.583436]brlan:端口3(lan3)进入禁用状态
[ 11.588709] mt7530-mdio mdio-bus:1f lan3: entered allmulticast mode
[ 11.596916] mt7530-mdio mdio-bus:1f lan3: entered promiscuous mode
[ 11.610895] mt7530-mdio mdio-bus:1f lan4: configuring for phy/gmii link mode
[ 11.621567] br-lan: port 4(lan4) entered blocking state
[ 11.626811] br-lan: port 4(lan4) entered disabled state
[ 11.632060] mt7530-mdio mdio-bus:1f lan4: entered allmulticast mode
[ 11.640352] mt7530-mdio mdio-bus:1f lan4: entered promiscuous mode
[ 11.886122] mtk_soc_eth 15100000.ethernet eth1: PHY [mdio-bus:07] driver [RTL8221B-VB-CG 2.5Gbps PHY (C45)] (irq=POLL)
[ 11.896818] mtk_soc_eth 15100000.ethernet eth1: configuring for phy/2500base-x link mode
11.588709]mt7530-mdio mdio-bus:1f lan3:输入allmultiast模式
[11.596916]mt7530-mdio mdio-bus:1f lan3:输入滥乱模式
[11.610895]mt7530-mdio mdio-bus:1f lan4:配置phy / gmii链路模式
[11.621567]brlan:端口4(lan4)进入阻塞状态
[11.626811]brlan:端口4(lan4)进入禁用状态
[11.632060]mt7530-mdio mdio-bus:1f lan4:输入allmultiast模式
[11.640352]mt7530-mdio mdio-bus:1f lan4:输入滥乱模式
[11.886122]mtk_soc_eth 1510万。以太网eth1:PHY[mdio-bus:07]驱动[rtl8221b - cg 2.5Gbps PHY(C45)](irq = POLL)
[11.896818]mtk_soc_eth 1510万。以太网eth1:配置for phy / 2500base-x链路模式
BusyBox v1.37.0 (2025-01-26 00:17:11 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r28694-730db6b893
OpenWrt快照,r28694-730db6b893
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
在这个设备上没有定义的根密码!
使用“passwd”命令设置一个新的密码
为了防止未经授权的SSH登录。
--------------------------------------------------
OpenWrt recently switched to the "apk" package manager!
OpenWrt最近转向“apk”包管理器!
OPKG Command APK Equivalent Description
OPKG命令 APK当量 描述
------------------------------------------------------------------
opkg install <pkg> apk add <pkg> Install a package
opkg remove <pkg> apk del <pkg> Remove a package
opkg upgrade apk upgrade Upgrade all packages
opkg files <pkg> apk info -L <pkg> List package contents
opkg list-installed apk info List installed packages
opkg update apk update Update package lists
opkg search <pkg> apk search <pkg> Search for packages
opkg install <pkg>安装指定的软件包
apk add <pkg> apk添加< pkg > Install a package安装软件包
opkg remove <pkg>卸载指定的软件包 apk del <pkg> Remove a package删除包
opkg upgrade对已经安装的软件包进行升级 apk upgrade 升级 Upgrade all packages升级所有软件包
opkg files <pkg>列出属于某个软件包的所有文件 apk info -L <pkg>apk信息-L List package contents列出包内容
opkg list-installed列出所有已安装的包 apk info List installed packages列出已安装的软件包
opkg update opkg更新 apk update apk更新 Update package lists更新包列表
opkg search <pkg> opkg搜索<pkg> apk search <pkg> apk搜索<pkg> Search for packages搜索包裹
------------------------------------------------------------------
|
|
IP卡
狗仔卡
发表于 
收藏
支持
反对
提升卡
沉默卡
喧嚣卡
变色卡
千斤顶
显身卡
楼主