硬盘问题：用PM查C盘，说是Error

datafield

[这个贴子最后由datafield在 2004/09/26 07:18pm 第 1 次编辑]

用PowerQuestPartitionMagic 8.0 在dos下查C盘
（C盘为系统XP，NTF格式，以前是FAT32，在PM下转为NTF）
电脑的症状为不定时地无反应，必须按重启，且常在显示window欢迎界面时或更早时停止一切反应。
用PM查C盘的INFO显示：
Error #1516
Partition improperly dismounted.
Please refer to the online user guide for instruction on how to resolve this issue.
现在不知要怎么办才好且E文也不是很好，上网找online可能没有什么用。
由于硬盘上数据较多，想尽量保护。
急！看有没有什么软件可以用的，谢谢看贴与回帖。

iced

之前装安还原精灵或与其相关的软件没有????

wlxjing

为什么不用ＸＰ带的那个命令那？

wanglei

顶出来，我也遇到过，望高手看看~

superwuyou

format吧

13377488

有可能是你的硬盘中了 逻辑锁之类的病毒

MYQZT

逻辑锁是不会让你执行PQ的，看看硬盘是否有坏道、是否有异响？机箱电源供电不足也能出现你这种情况。

隐形侠

用Fdisk/mbr重写引导区。试试？

zrz444

找一下修复工具,网上有许多,修复一下就可以.很简单.还有就是你的系统可能有别的系统.

carldeng

I poked carefully at the computer with various tools attempting at all costs not to alter any data written to the disk. Using Linux (Knoppix stand alone bootable CD) I was able to view the partition and see that all my data was just fine. I tried Partition Magic and it reported the error message "partition improperly dismounted". While Partition Magic is able to cure many problems with partitions it was unable to fix this problem by itself. Searching for that term on the net I discovered the cure.
The fix was to run check disk (CHKDSK) to fix the way the file system was laid out. Specifically, "CHKDSK /p" was the command. However, a plain CHKDSK revealed a single bad sector so I actually ran "CHKDSK /r" which will fix the sector problem as well as the partition problem. Executing this command properly set the flags for the partition and file system so that it could be mounted and booted from once again.
But, the system was dead so how to run CHKDSK? That turned out to be very easy. Just boot from the Windows XP install disk. It allows for a console from which many common tools including CHKDSK are available to run from the CD.
I was back up and running in fairly easy order. My time invested in the actual fix was probably 5 minutes. However the computer took an hour or so to carry out that fix using CHKDSK. But once it was done I could boot with no problems.

carldeng

But, the system was dead so how to run CHKDSK? That turned out to be very easy. Just boot from the Windows XP install disk. It allows for a console from which many common tools including CHKDSK are available to run from the CD.
系统瘫痪后又如何执行CHKDSK命令哪？那是吃豆腐般的事情。只需要启动Windows XP启动盘。它提供的平台中有许多CD里头的通用工具包括CHKDSK。
I was back up and running in fairly easy order. My time invested in the actual fix was probably 5 minutes. However the computer took an hour or so to carry out that fix using CHKDSK. But once it was done I could boot with no problems.
我能够在相当容易的程序下备份和运行。实际的修复时间只用了5分钟。然而用CHKDSK就会用上我一个小时。一旦修复完成，我可以完全没问题的启动电脑。

邃蓝

很大机会是坏道,而且是在C盘里,检查一下吧