|
|
发表于 2005-8-25 22:26:25
|
显示全部楼层
[注意]深山红叶启动光盘（WinPE＆PE Builder）讨论专帖（违令者必删）
网上找到一个东西：UnCHK3，现在还没搞清楚怎么用，估计有戏，明天好好研究一下
说明文件如下：
----------------------------------------------------------------------------
INSTALL:
If you have previously installed an older version of UnCHK, you MUST install this version in a different directory -or- delete the older version';s program and INI file. "Installation" consists of extracting the "UnCHK.exe" and putting it wherever you want. If, when you run the program, it says you are missing MSVBVM50, You need to download this file from Microsoft:
ftp://ftp.microsoft.com/Softlib/MSLFILES/MSVBVM50.EXE
Save it to a temporary spot and run it. It will install the Visual Basic 5
run-time files you need. After you';ve finished the installation, you can delete the file you downloaded from Microsoft.
----------------------------------------------------------------------------
QUICK START:
Drop a CHK file on it -or- just run it.
----------------------------------------------------------------------------
FAQ:
What are the "Scan Depth" settings?
Whole files - In general, if your recovered CHK files are intact and
your file system was in good shape (not counting whatever happened to create the
CHK files!), you can just try to identify the CHK files. The "Whole files"
scan depth setting is the fastest and generates the fewest false recoveries.
It also misses the most... because... your file system is NEVER in good shape!
Embedded files - If your file system was so fragmented that you couldn';t
recover any complete files, this might find a few pieces. The "Embedded files"
option will check every single byte trying to locate little things that might
have been embedded in other documents. For example, pictures that were part of
Word documents. You should *NOT* use this scan depth setting unless everything
else has failed you *AND* you know you have embedded items that are worth
retrieving. The "Embedded files" scan depth setting is the slowest and generates
an excessive number of false recoveries. If you really want to use it because
you are desparate to try to recover something, you should consider blocking all
file types from being recovered except the file type you are trying to recover.
See the "What if I only want to recover a single type of file?" FAQ below for
instructions on how to block unwanted file types from being recovered.
Floppy disk - If the CHK files you are recovering came from a floppy disk (even
if you';ve since copied them to your hard drive), this setting might recover
something that the "Whole files" depth setting would miss. It checks inside the
recovered CHK files on the 128-byte boundaries looking for cross-linked files.
Cross-linked files are fairly rare, and with any luck the recovery program that
created your CHK files made copies of and cross-linked files. If so, this setting
won';t find anything more than the "Whole files" setting. The "Floppy disk" scan
depth setting is only slightly slower than the "Whole files" setting and will
generate more false recoveries.
Hard disk - Same as the above "Floppy disk", except this checks on 512-byte
boundaries. Your disk may use much larger clusters, so this might be a bit of
overkill, but at least your cluster size isn';t going to be *smaller* than 512
bytes.
----------------------------------------------------------------------------
FAQ:
How do I modify the INI file to add more file types?
The easy way is to drop a KNOWN GOOD file onto the UNCHK program. UNCHK will
automatically add an entry for that file type to the INI file. From then on,
UNCHK will know how to recover files of that type. More or less.
To manually edit the UNCHK.INI file, look in the same place as the UNCHK.EXE
program file.
The INI file format is a file extension followed by the hex-encoded file
header, a space, then some hex-encoded text that should appear in all files
of that type.
For example, a JPG file has a header that always starts with these bytes:
|
|
楼主: Climbing
闽公网安备35020302032614号 )
IP卡
狗仔卡
显身卡